oven

CT-C-non-standardOzone sterilization drying ovenIt's my company in the originalCT-C series hot air circulation ovenOzone sterilization drying ovenOn the basis of, according toThe drying equipment carefully designed and produced in accordance with the requirements of GMP is suitable for drying various raw materials, powders, powders, capsules, low moisture extracts, granules, granules, traditional Chinese medicine decoction pieces, as well as drying and sterilizing materials such as soft bottles, glass bottles, utensils and instruments, in compliance with GMP requirements.

2、 Characteristics:

This product uses a low-noise axial flow fan and a cooling fan that transports ozone,equipped withPLC programmable control system, human-machine interface display, digital printer printing record, automatic manual control, smooth process, easy operation,The heating and constant temperature process is smooth, and the temperature sensor used controls the temperature accurately. The dehumidification is timed and forced, and the entire box is a fully enclosed structure.

3、 Working principle:

The ozone generated by the ozone generator at room temperature is first forced into the working room by a cooling fan through a regulating plate to achieve ozone sterilization. After the ozone work is completed, the heating switch is turned on,Under the action of forced ventilation, preheated clean strong wind is sent through a circulating fan. After being adjusted by the air conditioning plate inside the box, the hot air is evenly distributed and heats the material. At the same time, the clean air is further supplemented through the air inlet, and the humid air is forced out of the box by the dehumidification fan through the dehumidification outlet. This process repeats to achieve the effect of drying and sterilization.

4、 Technical requirements and specifications

1. Production capacity: maximum drying capacity per timesterilization80 pieces.

2. Operating temperature: room temperature50～120 ℃ (adjustable).

3Heating source: electric heating,heating power18KW、 Voltage 220V, made of stainless steel "U" - shaped non transparent thermal power heating tube, installed in the top air duct layer of the box.

4Install at the top of the box1Cooling fan and1Set of ozone generator, the ozone generated by the ozone generator is sent into the working room through the cooling fan and pipeline, and the cooling fan power0.25KW.

5The ozone generator is made of a combination of ceramic tubes, transformers, ozone generation chambers, etc., and produces ozone16g/hOzone concentration≥100PPM.

6. In order to shorten the drying time, improve the drying efficiency, and ensure that the hot air is evenly sent into every corner of the box to ensure the uniformity of temperature in each layer, one hot air circulation axial flow fan is installed on the right side of the box, with a total air volume7500m³/h， Fan power 055KW/2Platform, voltage380V is a high-temperature resistant cast aluminum fan.

7. Supporting drying car2Vehicle,The drying rack is made by combining the track, push rod, and drying wheel for placing the drying tray4040×δ1.5Made of mm stainless steel tube square tube, reinforced with welded vertical tube in the middle of the drying car to extend its service life. The track is made of 3042B δ 2.0mm stainless steel plate bent into angle steel, and the drying wheel is made of high-temperature resistant nylon wheel.

8. The external dimensions of the drying car are: face width650X depth 950 (mm), to ensure that the drying car does not deform during long-term use.

9. Supporting plastic frame80Only, the size is:600×400×60（mm），(Customer provided).

10. The four corners of the inner surface of the box are fully welded, polished, and polished for easy cleaning and smooth hot air flow. The outer surface of the box is smooth, flat, and aesthetically pleasing, meeting the requirements of "GMP".

11. The joints of the surface plates inside the box are all formed by argon arc welding, and they are made as a complete assembly.

12. The box door is a front opening door, with a total of 2 doors, and the door structure is an inner flat door structure，The door pressure strip is a high-temperature resistant silicone rubber sealing strip with excellent insulation performance.

13. To supplement the fresh air inside the box and meet the cleanliness requirements, one air inlet is made at the upper opening of the hot air circulation fan on the top of the oven, and a high-temperature and high-efficiency filter is installed. There is one air inlet for this box.

14. At the top, a dehumidification port is made and a high-temperature and high-efficiency filter is installed. There is one dehumidification port in this box, which is connected by an air duct. Then, a forced dehumidification fan is installed on top, which is a time proportional forced dehumidification fan with a power of 0.25KW and 380V, totaling one unit.

15. To prevent the drying efficiency of the materials inside the box from being affected when the dehumidification air volume is slightly high, one exhaust valve (Honeywell, USA) is installed at the dehumidification outlet, and the size of the dehumidification air volume can be adjusted.

16. The high-temperature and high-efficiency filters of the top air inlet and dehumidification air outlet devices of the box are made in a quick install manner, which is easy to disassemble and clean.

17. To ensure the long-term use of the bottom plate inside the box without deformation and smooth entry and exit of the drying car, the bottom plate inside the box is made of 3042B δ 2mm thick stainless steel plate.

18. The track groove on the bottom plate of the box is a concave convex closed track groove, which is made on the bottom plate of the box body to facilitate insulation and prevent miscellaneous bacteria from entering the box body, and to ensure that there are no hidden dirt gaps or dead corners inside the box.

19. Two sets of inclined feeding racks are used for the entry and exit of the supporting drying car, made of 3042B stainless steel plate with a thickness of δ3.0mm， The hinges on the inclined feeding rack are a set of stainless steel round steel locking hinges.

20. The external dimensions of the box are: face width2500 x Depth 1200 x height 2250 (mm), the outer surface plate is 3042B stainless steel plate δ1.2mm， All are laminated sub light plates. Remove the top cooling fan and exhaustThe height of the wet fan is, the actual height is1960mm

21. Studio size: Facade width1500 x Depth 1000 x Height 1500 (mm), the inner surface plate is made of 3042B stainless steel plate δ1.2mm， For laminated sub light plates.

22. In order to minimize temperature loss inside the box, save energy consumption, and ensure the temperature in the working environment, the insulation layer thickness of the box is80mm， Fill the insulation layer with high-temperature and fire-resistant insulation cotton.

23. To ensure that the hot air is evenly sent into the box, air distribution plates are installed outside the left and right air ducts inside the box to facilitate the uniform distribution of hot air inside the box.

24. The control system device of the box is located on the side panel of the oven and on the same side as the axial flow fan.

25The electrical control system of this box isPLC programmable control, human-machine interface display, temperature and time recording process for real-time printing by digital printer.

26. The materials, running deadlines, and cumulative running time of each variety being dried can be displayed on the touch screen and recorded on a paper recorder through computer printing.

27. Install one verification hole on each side of the box, made of DN25 semi sealed quick release clamp.

5、 Main technical parameters:

1. Model:non-standard

2. Heating source: electric heating

3. Maximum drying capacity（only）： 80

4. Temperature range (℃): Room temperature40～120 adjustable

5. Temperature used for ozone sterilization (℃): room temperature10～45 adjustable

6. Ozone production (g/h):16

7. Ozone concentration (PPm): ≥ 100

8. Heating power (kw): 18

9. Fan power (kw): 055×2Taiwan

10. Power of dehumidification fan (kw): 0.25 × 1 unit

11. Cooling fan power (kw): 025X 1 unit

12. Drying car size (mm):650×950

13. Number of drying cars (vehicles):2

14plastic crateSize（mm）： 600×400×60

15plastic crateQuantity (only): 80

16. Oven dimensions (mm): Face width2500 x Depth 1200 x height 2250

17. Oven studio size (mm): face width1500 x Depth 1000 x Height 1500

18. Control mode: PLC programmable control, human-machine interface display

Digital printer

19. Verification hole: DN25 semi sealed quick release clamp